Your cart is empty
Case
Case
-
4-3/4" Cross Arm Puller Tool
VT#: 16-0499 Cross arm puller tool is a 1" square bar 4-3/4" long and slotted with 3/8" x 16 bolts. Use any size bolt to pull gears and sprockets... VT#: 16-0499 Cross arm puller tool is a 1" square bar 4-3/4" long and slotted w... -
Bearing Tool
VT#: 16-0140 OEM Part Number: 97225-55 Sprocket shaft Timken bearing installer tool. FL Electra Glide® 1955-1984 FX Super Glide® 1971-1984... VT#: 16-0140 OEM Part Number: 97225-55 Sprocket shaft Timken bearing installer ... -
Bushing Reaming Tool
VT#: 16-0978 OEM Part Number: 94814-80A This eastern bushing reaming tool fits pinion bushing in cam cover. FL Electra Glide® 1955-1957 VT#: 16-0978 OEM Part Number: 94814-80A This eastern bushing reaming tool fits ... -
Bushing Reaming Tool
VT#: 16-0979 OEM Part Number: 94813-80A This eastern bushing reaming tool fits pinion bushing in cam cover. FL Electra Glide® 1941-1954 VT#: 16-0979 OEM Part Number: 94813-80A This eastern bushing reaming tool fits ... -
Case Boring Plate Tool with Screws
VT#: 16-1867 This boring fixture is designed to simplify and reduce the time required to prepare the crankcase and cylinder heads for big bore kit... VT#: 16-1867 This boring fixture is designed to simplify and reduce the time re... -
Case Lap Head
VT#: 16-0893 Case lap head only has an outer diameter of 1-3/4". All models VT#: 16-0893 Case lap head only has an outer diameter of 1-3/4". All models ... -
Case Lap Tool
VT#: 16-1835 Jims case lap tool features a lap which is supported on both sides by a pilot on the bushing side and plate which locates on the case... VT#: 16-1835 Jims case lap tool features a lap which is supported on both sides... -
Combo Engine and Transmission Lapping Tool
VT#: 16-0039 This combo lapping tool is used for precision alignment of engine and transmission shafts. Rod laps are not included. EL 1936-1940 FL... VT#: 16-0039 This combo lapping tool is used for precision alignment of engine ... -
Connecting Rod Bushing Tool Set
VT#: 16-0539 Connecting rod bushing tool set Replica connecting rod clamping tool, piston pin bushing tool and a V-Twin motor service patch. All... VT#: 16-0539 Connecting rod bushing tool set Replica connecting rod clamping to... -
Connecting Rod Clamping Tool
VT#: 16-0029 OEM Part Number: 233 Replica connecting rod clamping tool All models Allows rod to be held for straightening or to replace wrist pin... VT#: 16-0029 OEM Part Number: 233 Replica connecting rod clamping tool All mode...
New Products For October - Classic Pre-1984
$51.50Jims Hard Cap Tool
VT#: 16-0666Jims hard cap tool protects shaft when using press. FL Electra Glide...
$123.38Jims Sprocket Shaft Holder Too
VT#: 16-0683Jims sprocket shaft holder tool holds the flywheel assembly in a vis...
$58.23Engine Stand
VT#: 16-0543Engine stand tool for 1948-1999 Big Twin and TC-88. Use with an auto...
$135.12Sprocket Shaft Seal and Lock I
VT#: 16-0888OEM Part Number: 97235-55BSprocket shaft seal wrench tool installs a...
$142.56S&S Degree Wheel Kit
VT#: 16-0909This wheel kit is designed to fit the sprocket shaft and also includ...-
$220.86
Case Lap Head
VT#: 16-0893Case lap head only has an outer diameter of 1-3/4". All models ... 
$249.29Jims Timken Bearing Race Insta
VT#: 16-0668OEM Part Number: 94547-80AJims Timken bearing race installer tool is...
$81.25Jim Timken Bearing Simulator T
VT#: 16-0706OEM Part Number: 1745Jim Timken bearing simulator tool is designed t...
